Разработка TDA7317+TDA7439+LCD1602_i2C+ENCODER+IR

#define BRIG_H 200      // Яркость 0...255 POWER ON
#define BRIG_L 50       // Яркость 0...255 POWER OFF

#define IR_1 0x2FDD02F // Кнопка вверх
#define IR_2 0x2FD32CD // Кнопка вниз
#define IR_3 0x2FD906F // Кнопка >
#define IR_4 0x2FDF20D // Кнопка <
#define IR_5 0x2FD6A95 // Кнопка IN
#define IR_6 0x2FDEA15 // Кнопка MUTE
#define IR_7 0x2FD00FF // Кнопка STANDBY (POWER)

#define CLK     9   //  ENCODER 
#define DT      8   //  ENCODER 
#define SW     10   //  ENCODER 

#include <Wire.h>
#include <EEPROM.h>
#include <MsTimer2.h>                    // http://rcl-radio.ru/wp-content/uploads/2018/11/MsTimer2.zip
#include <Encoder.h>                     // http://rcl-radio.ru/wp-content/uploads/2019/05/Encoder.zip
#include <LiquidCrystal_I2C.h>           // http://forum.rcl-radio.ru/misc.php?action=pan_download&item=45&download=1 
#include <boarddefs.h>                   // входит в состав библиотеки IRremote
#include <IRremote.h>                    // http://rcl-radio.ru/wp-content/uploads/2019/06/IRremote.zip 
#include <TDA7439.h>                     // http://rcl-radio.ru/wp-content/uploads/2019/01/TDA7439.zip
#include <TDA7317.h>                     // https://github.com/liman324/TDA7317.git
 TDA7439 tda;
 TDA7317 tda1;
 Encoder myEnc(CLK, DT);
 LiquidCrystal_I2C lcd(0x27,16,2);  // Устанавливаем дисплей 
 IRrecv irrecv(12); // указываем вывод модуля IR приемника
 decode_results ir; 

 int menu,in,gain,vol,balans,band1,band2,band3,band4,band5,a[3],q[5],qqq[5],qi,qq,chl,chr;
 int gain0,gain1,gain2,gain3,gain4,times_in,vol_old;
 unsigned long times,times1,oldPosition  = -999,newPosition;
 byte m0=1,m1,i,d1,d2,d3,d4,d5,d6,e1,e2,e3;
 bool w,w2,gr1,gr2,power,www,in_x,mute;


void setup() {
  Serial.begin(9600);Wire.begin();irrecv.enableIRIn(); 
  MsTimer2::set(1, to_Timer);MsTimer2::start();
  if(EEPROM.read(100)!=0){for(int i=0;i<101;i++){EEPROM.update(i,0);}}// очистка памяти при первом включении 
  pinMode(A0,INPUT_PULLUP); // MUTE
  pinMode(A1,INPUT_PULLUP); // INPUT
  pinMode(A2,INPUT_PULLUP); // POWER
  pinMode(SW,INPUT);        // BUTTON SW ENCODER
  pinMode(6,OUTPUT);        // ВЫХОД УПРАВЛЕНИЯ ПОДСВЕТКОЙ
  pinMode(7,OUTPUT);        // ВЫХОД УПРАВЛЕНИЯ STANDBY
  analogWrite(6, BRIG_H);// больше 200 не делать
  vol = EEPROM.read(0);in = EEPROM.read(1);
  gain1 = EEPROM.read(2);gain2 = EEPROM.read(3);gain3 = EEPROM.read(4);gain4 = EEPROM.read(5);
  balans = EEPROM.read(6)-4;
  q[0] = EEPROM.read(7)-100;q[1] = EEPROM.read(8)-100;q[2] = EEPROM.read(9)-100;q[3] = EEPROM.read(10)-100;q[4] = EEPROM.read(11)-100;
  lcd.init();lcd.backlight();
  lcd.setCursor(5,0);lcd.print("TDA7439");
  lcd.setCursor(5,1);lcd.print("TDA7317");
  delay(1000);
     switch(in){
     case 1: gain0 = gain1;break;
     case 2: gain0 = gain2;break;
     case 3: gain0 = gain3;break;
     case 4: gain0 = gain4;break;
     } 
  audio();cl(); 

}

void loop() {
  if(power==1){digitalWrite(7,LOW);}else{digitalWrite(7,HIGH);}
  if ( irrecv.decode( &ir )) {Serial.print("0x");Serial.println( ir.value,HEX);irrecv.resume();times=millis();w=1;w2=1;}// IR приемник - чтение, в мониторе порта отображаются коды кнопок
  if(ir.value==0){gr1=0;gr2=0;}// запрет нажатий не активных кнопок пульта  

  if(m0==1){m0=0;
    byte v1[8] = {0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x07};
    byte v2[8] = {0x07,0x07,0x00,0x00,0x00,0x00,0x00,0x00};      
    byte v3[8] = {0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x1F};
    byte v4[8] = {0x1F,0x1F,0x00,0x00,0x00,0x00,0x1F,0x1F};
    byte v5[8] = {0x1C,0x1C,0x00,0x00,0x00,0x00,0x1C,0x1C};
    byte v6[8] = {0x1C,0x1C,0x1C,0x1C,0x1C,0x1C,0x1C,0x1C};
    byte v7[8] = {0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x07};
    byte v8[8] = {0x1F,0x1F,0x00,0x00,0x00,0x00,0x00,0x00};
    lcd.createChar(1, v1);lcd.createChar(2, v2);lcd.createChar(3, v3);lcd.createChar(4, v4);lcd.createChar(5, v5);lcd.createChar(6, v6);lcd.createChar(7, v7);lcd.createChar(8, v8);}
  if(m1==1){m1=0;
    byte v1[8] = {0b00000, 0b00000, 0b00000, 0b00000, 0b00000, 0b00000, 0b00000, 0b01110};
    byte v2[8] = {0b00000, 0b00000, 0b00000, 0b00000, 0b00000, 0b00000, 0b01110, 0b01110};
    byte v3[8] = {0b00000, 0b00000, 0b00000, 0b00000, 0b00000, 0b01110, 0b01110, 0b01110};
    byte v4[8] = {0b00000, 0b00000, 0b00000, 0b00000, 0b01110, 0b01110, 0b01110, 0b01110};
    byte v5[8] = {0b00000, 0b00000, 0b00000, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110};
    byte v6[8] = {0b00000, 0b00000, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110};
    byte v7[8] = {0b00000, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110};
    byte v8[8] = {0b01110, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110, 0b01110};
    lcd.createChar(0, v1);lcd.createChar(1, v2);lcd.createChar(2, v3);lcd.createChar(3, v4);lcd.createChar(4, v5);lcd.createChar(5, v6);lcd.createChar(6, v7);lcd.createChar(7, v8);}

 if(power==0){
  /// MENU //////////////////////////////
  if(digitalRead(SW)==LOW){menu++;if(menu>2){menu=0;};switch(menu){case 0: m0=1;break;case 1: m1=1;break;case 2: m0=1;break;}delay(200);lcd.clear();w=1;w2=1;times=millis();w2=1;}
  if(ir.value==IR_1){menu++;gr1=0;gr2=0;cl1();times=millis();w=1;w2=1;if(menu>2){menu=0;};switch(menu){case 0: m0=1;break;case 1: m1=1;break;case 2: m0=1;break;}delay(200);lcd.clear();w=1;w2=1;times=millis();w2=1;}
  if(ir.value==IR_2){menu--;gr1=0;gr2=0;cl1();times=millis();w=1;w2=1;if(menu<0){menu=2;};switch(menu){case 0: m0=1;break;case 1: m1=1;break;case 2: m0=1;break;}delay(200);lcd.clear();w=1;w2=1;times=millis();w2=1;}
 
  /// INPUT ////////////////////////////
  if((digitalRead(A1)==LOW||ir.value==IR_5)&&menu!=1){in++;gr1=0;gr2=0;if(in>4){in=1;}menu=100;w=1;w2=1;in_x=1;times=millis();cl();delay(200);}
 
 /// MUTE //////////////////////////////
 if((digitalRead(A0)==LOW||ir.value==IR_6)&&mute==0){mute=1;gr1=0;gr2=0;menu=100;cl();lcd.setCursor(6,0);lcd.print("MUTE");vol_old=vol;vol=0;audio();}
 if((digitalRead(A0)==LOW||ir.value==IR_6)&&mute==1){mute=0;gr1=0;gr2=0;menu=0;m0=1;cl();w2=1;vol=vol_old;audio();}  
  }
 /// POWER ///////////////////////////// 
  if((ir.value==IR_7||digitalRead(A2)==LOW)&&power==0){power=1;cl();lcd.setCursor(3,0);lcd.print("POWER  OFF");menu=100;m0=1;
   vol_old=vol;vol=0;audio();delay(3000);analogWrite(6,BRIG_L);}// power off
  if((ir.value==IR_7||digitalRead(A2)==LOW)&&power==1){power=0;analogWrite(6, BRIG_H);cl();lcd.setCursor(3,0);lcd.print("POWER   ON ");
    vol=vol_old;audio();w2=1;w=1;menu=0;m0=1;myEnc.write(0);delay(2000);cl();}// power on

 
 /// VOLUME ///////////////////////////////////////////////////
 if(menu==0){
   if(ir.value==IR_3){vol++;gr1=1;gr2=0;cl1();times=millis();w=1;w2=1;vol_conf();audio();}// кнопка > 
   if(ir.value==0xFFFFFFFF and gr1==1){vol++;gr2=0;cl1();times=millis();w=1;w2=1;vol_conf();audio();}// кнопка >>>>>>
   if(ir.value==IR_4){vol--;gr1=0;gr2=1;cl1();times=millis();w=1;w2=1;vol_conf();audio();}// кнопка <
   if(ir.value==0xFFFFFFFF and gr2==1){vol--;gr1=0;cl1();times=millis();w=1;w2=1;vol_conf();audio();}// кнопка <<<<<<  
 
   if (newPosition != oldPosition){oldPosition = newPosition;
     vol=vol+newPosition;myEnc.write(0);newPosition=0;w=1;times=millis();w2=1;vol_conf();audio();}
     
     lcd.setCursor(0,0);lcd.print("VOLUME ");
     lcd.setCursor(0,1);lcd.print("INPUT ");lcd.print(in);
 
  if(w2==1){w2=0;
     a[0]=(vol)/10;a[1]=(vol)%10;
       for(int i=0;i<2;i++){
      switch(i){
        case 0: e1=9,e2=10,e3=11;break;
        case 1: e1=12,e2=13,e3=14;break;
        }
      switch(a[i]){
        case 0: d1=1,d2=8,d3=6,d4=1,d5=3,d6=6;break;
        case 1: d1=32,d2=2,d3=6,d4=32,d5=32,d6=6;break;
        case 2: d1=2,d2=8,d3=6,d4=1,d5=4,d6=5;break;
        case 3: d1=2,d2=4,d3=6,d4=7,d5=3,d6=6;break;
        case 4: d1=1,d2=3,d3=6,d4=32,d5=32,d6=6;break;
        case 5: d1=1,d2=4,d3=5,d4=7,d5=3,d6=6;break;
        case 6: d1=1,d2=4,d3=5,d4=1,d5=3,d6=6;break;
        case 7: d1=1,d2=8,d3=6,d4=32,d5=32,d6=6;break;
        case 8: d1=1,d2=4,d3=6,d4=1,d5=3,d6=6;break;
        case 9: d1=1,d2=4,d3=6,d4=7,d5=3,d6=6;break;
    }
      lcd.setCursor(e1,0);lcd.write((uint8_t)d1);lcd.setCursor(e2,0);lcd.write((uint8_t)d2);lcd.setCursor(e3,0);lcd.write((uint8_t)d3);
      lcd.setCursor(e1,1);lcd.write((uint8_t)d4);lcd.setCursor(e2,1);lcd.write((uint8_t)d5);lcd.setCursor(e3,1);lcd.write((uint8_t)d6);
 }} 
 }

// Equalizer /////////////////////////////////////
 if(menu==1){ 
   if(digitalRead(A1)==LOW||ir.value==IR_5){qi++;gr1=0;gr2=0;ir.value=0;if(qi>4){qi=0;}w=1;w2=1;delay(300);}
   switch(qi){
    case 0: qq=q[0];break;
    case 1: qq=q[1];break;
    case 2: qq=q[2];break;
    case 3: qq=q[3];break;
    case 4: qq=q[4];break;
    }
 
   if(ir.value==IR_3){qq++;gr1=1;gr2=0;cl1();times=millis();www=1;w=1;w2=1;eq_conf();}// кнопка > 
   if(ir.value==0xFFFFFFFF and gr1==1){qq++;gr2=0;cl1();times=millis();www=1;w=1;w2=1;eq_conf();}// кнопка >>>>>>
   if(ir.value==IR_4){qq--;gr1=0;gr2=1;cl1();times=millis();www=1;w=1;w2=1;eq_conf();}// кнопка <
   if(ir.value==0xFFFFFFFF and gr2==1){qq--;gr1=0;cl1();times=millis();www=1;w=1;w2=1;eq_conf();}// кнопка <<<<<<   
 
   if (newPosition != oldPosition){oldPosition = newPosition;
     qq=qq+newPosition;myEnc.write(0);newPosition=0;w=1;times=millis();w2=1;eq_conf();www=1;}
   if(www==1){www=0;q[qi]=qq;audio();}
 
  for (int pos = 0; pos < 5; pos++) {lcd.setCursor(pos, 0);
    qqq[pos] = map(q[pos],-7,7,0,15);
    if (qqq[pos] > 7){lcd.write((uint8_t)qqq[pos] - 8);lcd.setCursor(pos, 1);lcd.write((uint8_t)7);} 
    else {lcd.print(" ");lcd.setCursor(pos, 1);lcd.write((uint8_t)qqq[pos]);}}
    lcd.setCursor(7,0);lcd.print("F ");
    switch(qi){
      case 0: lcd.print("60  Hz");break;
      case 1: lcd.print("260 Hz");break;
      case 2: lcd.print("1  kHz");break;
      case 3: lcd.print("3  kHz");break;
      case 4: lcd.print("10 kHz");break;
      }
    lcd.setCursor(7,1);lcd.print("G ");lcd.print(q[qi]*2);lcd.print(" dB  ");
 } 

 //////// BALANCE /////////////////////////////////////////////////////////////// 
 if(menu==2){ 
   if(ir.value==IR_3){balans++;gr1=1;gr2=0;cl1();times=millis();www=1;w=1;w2=1;ball_fun();}// кнопка > 
   if(ir.value==0xFFFFFFFF and gr1==1){balans++;gr2=0;cl1();times=millis();www=1;w=1;w2=1;ball_fun();}// кнопка >>>>>>
   if(ir.value==IR_4){balans--;gr1=0;gr2=1;cl1();times=millis();www=1;w=1;w2=1;ball_fun();}// кнопка <
   if(ir.value==0xFFFFFFFF and gr2==1){balans--;gr1=0;cl1();times=millis();www=1;w=1;w2=1;ball_fun();}// кнопка <<<<<<  
 
   if (newPosition != oldPosition){oldPosition = newPosition;
   balans=balans-newPosition;myEnc.write(0);newPosition=0;times=millis();w=1;w2=1;ball_fun();www=1;
   }
   if(www==1){www=0;audio();}
   
   lcd.setCursor(4,0);lcd.print(F("   <>   "));lcd.setCursor(4,1);lcd.print(F("CHL  CHR"));
   chl=(4+balans)-4;chr=(4-balans)-4;
   if(chl<0){lcd.setCursor(12,0);chl=abs(chl);lcd.write((uint8_t)3);}else{lcd.setCursor(12,0);lcd.print(" ");}
   if(chr<0){lcd.setCursor(0,0);chr=abs(chr);lcd.write((uint8_t)3);}else{lcd.setCursor(0,0);lcd.print(" ");}
   if(w2==1){w2=0;a[0]=chl;a[1]=chr;
   for(int i1=0;i1<2;i1++){
      switch(i1){
        case 0: e1=1,e2=2,e3=3;break;
        case 1: e1=13,e2=14,e3=15;break;
        }
      switch(a[i1]){
        case 0: d1=1,d2=8,d3=6,d4=1,d5=3,d6=6;break;
        case 1: d1=32,d2=2,d3=6,d4=32,d5=32,d6=6;break;
        case 2: d1=2,d2=8,d3=6,d4=1,d5=4,d6=5;break;
        case 3: d1=2,d2=4,d3=6,d4=7,d5=3,d6=6;break;
        case 4: d1=1,d2=3,d3=6,d4=32,d5=32,d6=6;break;
        case 5: d1=1,d2=4,d3=5,d4=7,d5=3,d6=6;break;
        case 6: d1=1,d2=4,d3=5,d4=1,d5=3,d6=6;break;
        case 7: d1=1,d2=8,d3=6,d4=32,d5=32,d6=6;break;
        case 8: d1=1,d2=4,d3=6,d4=1,d5=3,d6=6;break;
        case 9: d1=1,d2=4,d3=6,d4=7,d5=3,d6=6;break;
    }
      lcd.setCursor(e1,0);lcd.write((uint8_t)d1);lcd.setCursor(e2,0);lcd.write((uint8_t)d2);lcd.setCursor(e3,0);lcd.write((uint8_t)d3);
      lcd.setCursor(e1,1);lcd.write((uint8_t)d4);lcd.setCursor(e2,1);lcd.write((uint8_t)d5);lcd.setCursor(e3,1);lcd.write((uint8_t)d6);
 }}}    


////////////////////////// GAIN IN /////////////////////////////////////////////////////////////////////////////////////
if(in_x==1){ menu=100;
   switch(in){
     case 1: gain0 = gain1;break;
     case 2: gain0 = gain2;break;
     case 3: gain0 = gain3;break;
     case 4: gain0 = gain4;break;
     }
 
     if(ir.value==IR_3){gain0++;gr1=1;gr2=0;cl1();times=millis();www=1;w=1;gain_func();}// кнопка > 
     if(ir.value==0xFFFFFFFF and gr1==1){gain0++;gr2=0;cl1();times=millis();www=1;w=1;gain_func();}// кнопка >>>>>>
     if(ir.value==IR_4){gain0--;gr1=0;gr2=1;cl1();times=millis();www=1;w=1;gain_func();}// кнопка <
     if(ir.value==0xFFFFFFFF and gr2==1){gain0--;gr1=0;cl1();times=millis();www=1;w=1;gain_func();}// кнопка <<<<<<  
 
    if (newPosition != oldPosition) {oldPosition = newPosition;
    gain0=gain0+newPosition;myEnc.write(0);newPosition=0;times=millis();www=1;w=1;gain_func();} 
 
   switch(in){
     case 1: gain1 = gain0;break;
     case 2: gain2 = gain0;break;
     case 3: gain3 = gain0;break;
     case 4: gain4 = gain0;break;
     }
 
  if(www==1){www=0;audio();}
  lcd.setCursor(3,0);lcd.print("INPUT ");lcd.print(in);lcd.setCursor(3,1);lcd.print("GAIN ");lcd.print(gain0);lcd.print(" dB ");
   }

//// EEPROM ///////////////////////////////////////
   if(in_x==1){times_in=3000;}else{times_in=10000;}
   if(millis()-times>times_in && w==1 && power==0 && mute==0){w=0;in_x=0;EEPROM.update(0,vol);EEPROM.update(1,in);
   EEPROM.update(2,gain1);EEPROM.update(3,gain2);EEPROM.update(4,gain3);EEPROM.update(5,gain4);
   EEPROM.update(6,balans+4);
   EEPROM.update(7,q[0]+100);EEPROM.update(8,q[1]+100);EEPROM.update(9,q[2]+100);EEPROM.update(10,q[3]+100);EEPROM.update(11,q[4]+100);
   menu=0;cl();m0=1;w2=1;
}   

}  // END LOOP

void gain_func(){if(gain0<0){gain0=0;}if(gain0>15){gain0=15;}}
void ball_fun(){if(balans>4){balans=4;}if(balans<-4){balans=-4;}}
void eq_conf(){if(qq>7){qq=7;}if(qq<-7){qq=-7;}}
void vol_conf(){if(vol>48){vol=48;} if(vol<0){vol=0;}}
void cl(){ir.value=0;delay(300);lcd.clear();}
void cl1(){ir.value=0;delay(200);} 

void audio(){
  tda.setInput(in); // 1 to 4 // номер канала
  tda.inputGain(gain); // 0 to 15 // усиление 
  tda.setVolume(vol); // 0 to 48 ( 0 is mute) // громкость
  tda.setSnd(0, 1); //-7 to +7 , 1 - Bass | 2 - Mids | 3 - Trebble
  tda.setSnd(0, 2);
  tda.setSnd(0, 3); 
  tda.spkAtt(4-balans, 4+balans); // баланс R L от 0 to 79 (db) 
  /////////// номер полосы, дБ (-7...+7) //////////
  tda1.setBand(0,q[4]);  // 10000 Hz
  tda1.setBand(1,q[3]);  // 260   Hz
  tda1.setBand(2,q[2]);  // 1000  Hz
  tda1.setBand(3,q[1]);  // 3000  Hz
  tda1.setBand(4,q[0]);  // 60    Hz
}
void to_Timer(){newPosition = myEnc.read()/4;}